Home > Error The > Cacti Install Spine

Cacti Install Spine

Contents

Remove old rra data that does not confuse with the new data of spine poller. fogingMay 31st, 2007, 10:17 PMAnd paste this in there: #!/bin/sh # # Fancontrol start script. # set -e # Defaults DAEMON=/usr/sbin/fancontrol PIDFILE=/var/run/fancontrol.pid PATH=/sbin:/bin:/usr/sbin:/usr/bin test -f $DAEMON || exit 0 . /lib/lsb/init-functions If any of you have any advice please give it! hwmon1/device/fan2_input ... have a peek at these guys

Configuring Cacti Now you need to point your browser http://serverip/cacti press enter.You should see similar to the following screen Click Next to Continue. After I unloaded and reloaded the module, I noticed that when I ran 'sudo sensors' I had lost the CPU fan reading (it now reported 0 rpm with div=2), and that The program will attempt to restore each fan to full speed after testing. n Testing pwm control hwmon1/device/pwm2 ... more info here

Error The Path /usr/sbin/spine Is Invalid

However, it is ** very important ** that you physically verify that the fans have been to full speed after the program has completed. Testing pwm control 0-002e/pwm3 ... /usr/sbin/pwmconfig: line 117: 0-002e/pwm3_enable: Permission denied 0-002e/fan1_input ... Login Register FAQ Search It is currently Fri Oct 14, 2016 5:03 pm

View unanswered posts | View active topics Board index » Cacti - Support

You can also delete the /etc/fancontrol file if you don't intend to return to using fancontrol. skipping! Be carefull. (I use the fancontroller made by MSI for my motherboard on windows, which works for me, but is considered malware by others :) ) jotape99November 23rd, 2005, 12:17 AMThanks But still a great guide! ^^ Mark on July 27, 2009 at 10:43 am said: First of all great guide and very simple.

There is either no fan connected to the output of 0-002e/pwm1, or the connected fan has no rpm-signal connected to one of the tested fan sensors. (Note: not all motherboards have Spine Poller File Path Thanks again for a great how to! but.. http://www.ubuntugeek.com/install-and-configure-cacti-monitoring-tool-in-ubuntu-810-intrepid-ibex-server.html The only solution at the moment is almost unthinkable: returning to Windows where my fans are very quiet.

benplautJuly 25th, 2005, 10:04 AMI would seriously have a heart-attack just by trying this (I don't even need for it to _not_ work O.o). Can not continue From: Ahmed EL_Gamala yahoo ! skipping. ** Note: rivatv module is available at http://rivatv.sourceforge.net/ Module `i2c-sis96x' already loaded. There is either no fan connected to the output of 9191-0290/pwm1, or the connected fan has no rpm-signal connected to one of the tested fan sensors. (Note: not all motherboards have

Spine Poller File Path

Your MySQL connection id is 28894 Server version: 5.0.77-community MySQL Community Edition (GPL) Type 'help;' or '\h' for help. check these guys out remmeltJune 20th, 2005, 07:59 PMDon't forget to $ sudo chmod 0755 /etc/init.d/fancontrol and create a symlink to that script in rc3.d, for example. $ sudo ln -s /etc/init.d/fancontrol /etc/rc3.d/S99fancontrol (thanks for Error The Path /usr/sbin/spine Is Invalid Code:chmod a+x spine Reinhard _________________Official Cacti DocumentationOfficial Debugging HelpCentral Plugin RepositoryCentral Templates Repository Top Kar_man Post subject: Posted: Tue Nov 13, 2007 5:06 pm Joined: Mon Feb 14, Cacti Spine Always unload the module between new modprobes, though, or it will just disregard the new load.

In my case my cpi heatsink is facing sideways, and the fan blows air from the front, across the heatsink, and out the back. However, it is ** very important ** that you physically verify that the fans have been to full speed after the program has completed. This is the output of the first run: ************************************************** ************* [email protected]:/etc/init.d$ sudo pwmconfig This program will search your sensors for pulse width modulation (pwm) controls, and test each one to see ExMachinaAugust 12th, 2006, 10:22 PMI choose ISA..

Actually, you probably want to note your exisiting configuration, so you can set it up the same way again using the original process. Probing for `Winbond W83781D' Trying address 0x0290... PS: I'm a linux-newbie, installed this last week.... check my blog Actually I think now its got to do with when I was compiling spine.

During shut down the fan speeds up! If you do not want to do this hit control-C now!!! If not, you won't be able to open any /dev/i2c-* file.

We will now try to load each adapter module in turn.

If you do not want to do this hit control-C now!!! This is usually safe though. Semi. Since yours are already full speed, you may not notice any immediate change.

Failed! Mark on July 27, 2009 at 2:47 pm said: thank you for your response but still the same problem i think the problem is with spine. but when i tried to patch, some errors destroyed my cacti installation :(, i has to roll back to save the installation… Alex on September 18, 2009 at 9:00 pm said: news I run an ASUS M2M-MX motherboard.

mail ! newsgator Bloglines iNezha TOR Shell Unlimited Webhosting - Shell Account Pages About Angkringan Downloads Most WantedCommands MyDesktop tagapache autoposting blank0n Cacti Coding compiz compiz fusion Debian distro linux docs emulator error Next weekend at the earliest. it looked to work..

Servers need all the cooling they can get, plus they are usually stored in places where no-one can hear the noise they make. The speed is being reported, so you won't have to change the fan's divisor. speed was 2556 now 2596 no correlation hwmon1/device/fan3_input ... This is true for the version currently in Hoary, version 2.8.8-7ubuntu2.

Set up lm-sensors and get output from sensors: k8temp-pci-00c3 Adapter: PCI adapter Core0 Temp: +37C w83627ehf-isa-0290 Adapter: ISA adapter VCore: +1.14 V (min = +0.00 V, max = +1.74 V) in1: I really gotta lower these fans, I've got low temperatures and a fan that sounds like a vacuum cleaner. I don't have the time right now! alibek (23 июля 2015 - 20:11) писал: vlad11 (23 июля 2015 - 16:42) писал: Вы хоть эксплуатировали cacti? У меня мониторится четыре сотни устройств (и сотен 6 datasource), с интервалом раз

How do I find out if I need a Linux driver, and what might that driver be? Automatic starting is also OK. Please note that the sections are according to chip name and NOT module name (I would imagine chip name and module name are usually the same, but they were a little u will see like this: poller spine then click save others configuration: 1.

Testing pwm control 0-002e/pwm2 ... /usr/sbin/pwmconfig: line 117: 0-002e/pwm2_enable: Permission denied 0-002e/fan1_input ... If you haven't changed your fan speed, it's set to maximum. Failed! Warning!!!

The fancontrol script can automatically respond to temperature changes of your system by changing fanspeeds. In the sensors.conf file, i found the section at line 1537. Most of this howto is from here: http://www.fedoraforum.org/forum/showpost.php?p=161610&postcount=5 Check if your hardware is supported here: http://www.almico.com/forumindex.php Mr WonkaJune 19th, 2005, 11:46 PMAnd if you want to have it startup on boot.